Cookies Policy
The website need some cookies and similar means to function. If you permit us, we will use those means to collect data on your visits for aggregated statistics to improve our service. Find out More
Accept Reject
  • Menu
Publications

Publications by João Miguel Maia

2019

Mass Producible Low-Loss Broadband Optical Waveguides in Eagle2000 by Femtosecond Laser Writing

Authors
Amorim, VA; Viveiros, D; Maia, JM; Marques, PVS;

Publication
IEEE PHOTONICS TECHNOLOGY LETTERS

Abstract
Optical waveguides were fabricated in alkaline earth boro-aluminosilicate glass, by femtosecond laser direct writing, with varying pulse energy and scan velocity. A spectral characterization, from 500 nm to 1700 nm, was made in order to determine their losses and understand its dependence on the processing parameters. Three major loss mechanisms were identified. At longer wavelengths, loss is mainly due to weak coupling. On the other hand, the behavior at shorter wavelengths is governed by propagation loss due to Rayleigh scattering, which was shown to be practically eliminated (& x003C; 0.05 dB $\cdot$ cm $<^>{-1} {\cdot }\,\,\mu \text{m}<^>{4}$ ) at higher scan velocities. Bulk absorption was also found to have an influence in the propagation losses at higher wavelengths. The combination of intermediate pulse energies (between 125-250 nJ) and high scan velocities (above 6 cm/s) allowed the fabrication of optical waveguides offering low losses across the entire range of wavelengths tested, facilitating applications that require larger wavelength working bands. Furthermore, since optimal fabrication conditions are achieved at higher scanning velocities, mass production with reduced fabrication times can be achieved.

2019

Addressing the Fabrication Difficulties of Femtosecond Laser Written Surface Waveguides for Enhanced Evanescent Coupling

Authors
Amorim, VA; Maia, JM; Viveiros, D; Marques, PVS;

Publication
EPJ Web of Conferences

Abstract
In this work, the fabrication of optical waveguides embedded in fused silica (Suprasil1) and boro-aluminosilicate glass (Eagle2000) is demonstrated with femtosecond laser direct writing, as well as their suitability to be brought to the surface, through wet etching, for enhanced evanescent coupling with the external dielectric medium. Fused silica demonstrated to be inappropriate in this particular application, as the guiding region is at the bottom of the induced modification, creating a barrier between the guided mode and the substrate’s boundary. Furthermore, the existence of nanogratings meant that, upon contact of the top of the induced modification with the substrate’s boundary, the waveguide is quickly etched. Eagle2000 demonstrated to be superior to fused silica due to its characteristic modification cross-section and absence of nanogratings, which allowed the placement of the guiding region as close to the substrate’s surface as required. However, surface roughness arising from the creation of insoluble products in the HF solution was found. The addition of HCl to dissolve these products was implemented.

2019

Fabrication of periodic structures in optical fibers by femtosecond laser micromachining for sensing applications

Authors
Viveiros, D; Maia, JM; Amorim, VA; Jorge, PAS; Marques, PVS;

Publication
FOURTH INTERNATIONAL CONFERENCE ON APPLICATIONS OF OPTICS AND PHOTONICS

Abstract
A femtosecond laser direct writing system was developed to explore the fabrication of periodic structures in optical fibers. The possibility to write type I first- and second-order Bragg gratings in the same single-mode fiber (SMF-28e), with reflectivities of 99.6 % and 59.3 %, respectively, is presented. The fabrication of structures (waveguides and grating) in a coreless and in a SMF-28e fiber was first demonstrated, and the gratings were then exposed to a thermal annealing up to 1000 degrees C. The FBG inscribed in the SMF-28e fiber presents thermal stability at temperatures of 800 degrees C and a temperature sensitivity of 14.34 pm/degrees C was determined.

2019

Femtosecond Laser Micromachining of Fabry-Pérot Interferometers for Magnetic Field Sensing

Authors
Maia, JM; Amorim, VA; Viveiros, D; Marques, PVS;

Publication
EPJ Web of Conferences

Abstract
Fs-laser micromachining is a high precision fabrication technique that can be used to write novel three-dimensional structures, depending on the nature of light-matter interaction. In fused silica, the material modification can lead to (i) an increase of the refractive index around the focal volume, resulting in the formation of optical circuits, or (ii) an enhancement of the etch rate of the laser-affected zones relative to the pristine material, leading to a selective and anisotropic etching reaction that enables fabrication of microfluidic systems. Here, both effects are combined to fabricate a Fabry-Pérot interferometer, where optical waveguides and microfluidic channels are integrated monolithically in a fused silica chip. By filling the channel with a magnetic fluid whose refractive index changes with an external magnetic field, the device can be used as a magnetic field sensor. A linear sensitivity of -0.12 nm/mT is obtained in the 5.0±0.5 to 33.0±0.5 mT range, with the field being applied parallel to the light propagation direction.

2020

Magnetic field sensors in fused silica fabricated by femtosecond laser micromachining

Authors
Maia, JM; Amorim, VA; Viveiros, D; Marques, PVS;

Publication
JOURNAL OF PHYSICS-PHOTONICS

Abstract
Based on the characteristics of ferrofluids, a monolithic optofluidic device for magnetic field sensing is proposed and demonstrated. The device consists of a Fabry-Perot interferometer, composed by an optical waveguide orthogonal to a microfluidic channel, which was fabricated inside a fused silica substrate through femtosecond laser micromachining. The interferometer was first optimized by studying the influence of the waveguide writing parameters on its spectral properties. Waveguides written at higher pulse energies led to a decrease of the signal-to-noise ratio, due to an enhancement of micrometer sized defects associated with Mie scattering. Fringe visibility was also maximized for waveguides written at lower scanning speeds. Making use of the tunable refractive index property exhibited by magnetic fluids, the interferometer was then tested as a magnetic field sensor by injecting a ferrofluid inside the microfluidic channel. A linear sensitivity of -0.25 nm/mT was obtained in the 9.0-30.5 mT range with the external field parallel to the waveguide axis.

2020

Femtosecond laser direct written off-axis fiber Bragg gratings for sensing applications

Authors
Viveiros, D; Amorim, VA; Maia, JM; Silva, S; Frazao, O; Jorge, PAS; Fernandes, LA; Marques, PVS;

Publication
OPTICS AND LASER TECHNOLOGY

Abstract
First order off-axis fiber Bragg gratings (FBGs) were fabricated in a standard single mode fiber (SMF-28e) through femtosecond laser direct writing. A minimum offset distance between the grating and core center of 2.5 mu m was found to create a multimode section, which supports two separate fiber modes (LP0,1 and LP1,1), each split into two degenerate polarization modes. The resulting structure breaks the cylindrical symmetry of the fiber, introducing birefringence (approximate to 10(-4)) resulting in a polarization dependent Bragg wavelength for each mode. Based on the modal and birefringence behavior, three off-axis FBGs were fabricated with 3.0, 4.5 and 6.0 mu m offsets from the core center, and then characterized in strain, temperature, and curvature. The tested off-axis FBGs exhibited a similar strain sensitivity of similar to 1.14 pm/mu epsilon and a temperature sensitivity of similar to 12 pm/C. The curvature and orientation angle were simultaneously monitored by analyzing the intensity fluctuation and the wavelength shift of the LP1,1 Bragg resonance. A maximum curvature sensitivity of 0.53 dB/m(-1) was obtained for the off-axis FBG with a 3.0 mu m offset.

  • 3
  • 6