Abstract
A theoretical and experimental study of a new fiber loop mirror based on a "figure-of-eight" configuration, is reported. For the theoretical model, the Jones matrix analysis is analyzed. The configuration is tested as an interrogation system where the spectral response arises from the combination of the reference signal modulated by the sensor signal. The configuration is characterized in mechanical strain and presents a phase sensitivity of 8.2 mrad/mu epsilon.

Abstract
In this work, a novel high birefringent (HiBi) fiber loop mirror sensor based on a "figure-of-eight" constructed with a 3x3 fiber coupler, is presented. The "figure-of-eight" is formed by two fiber loop mirrors (FLM's) made by four of the six fiber arms of the 3x3 fiber coupler. The other two remaining fiber ports of the 3x3 coupler are used as input and output fibers of the compound sensor. The sensing head is located in the one of the FLM and it is formed by a spliced section of HiBi elliptical core fiber. The spectral response of this "figure-of-eight" configuration presents two interference optical signals that can be easily tuned by a polarization controller that is located in the other FLM, and which is made only of standard singlemode fiber from two arms of the 3x3 coupler. The sensor head was optically characterized both in temperature and strain, showing wavelength dependence sensitivities of -0.23 nm/degrees C and - 2.6 pm/mu epsilon, for temperature and strain, respectively. It is noticed that these sensitivities are practically the same for the two interference signals. Future work will explore the possibility to use the singlemode FLM to interrogate the sensor head made by HiBi fiber section, and providing elimination of phase fluctuations that can occur, increasing its potential for remote sensing applications.

Abstract
Fiber optic modal interferometry has been around as a sensing concept since the outcome of fiber optic sensing. Initially supported by the utilization of standard Hi-Bi fibres associated to polarimetric modal interference, later this sensing approach evolved to modal interference based on spatial modes propagating in the core, on spatial modes propagating in the core and in the cladding with coupling performed by fibre devices such as long period gratings and tapers, and more recently on several types of modes propagating in photonic crystal fibers. This paper will address fiber optic sensing based on modal interferometry, and configurations of different type researched in last years will be presented and their performance compared.

Abstract
An interferometric Fabry-Perot cavity based on hollow-core ring photonic crystal fiber (HCR-PCF) for pressure sensing is proposed. The sensing head is formed by splicing a small section of HCR-PCF to standard single mode fiber. The spectral response depends on the cavity length due to the geometry of the HCR-PCF. The sensing head is subjected to methane pressure variations, where it exhibits a sensitivity of 0.82 nm/MPa. Its response to nitrogen pressure variation is also studied. The sensing head's intrinsic sensitivity to the nitrogen refractive index variations inside the hollow-core is also estimated. Finally, temperature measurement is performed and a sensitivity of 3.77 pm/degrees C is obtained for temperatures below 200 degrees C.

Abstract
The spectral behavior in the C-band of fiber Bragg gratings (FBGs) was analyzed as a function of temperature and strain. The FBGs were fabricated in pure silica four-leaf-clover- shaped suspended-core fibers by (DUV) femtosecond laser exposure (3.6 W at 800 nm, 130 fs, 1 kHz frequency tripled to 350 fs, 650 mW at 267 nm). A defect fiber (with a hollow hole in the core) and nondefect fiber were compared both yielding approximate to 1 pm/mu epsilon sensitivity to strain but different sensitivity to temperature (from 3.0 pm/degrees C to 8.4 pm/degrees C for the defect fiber and 10 pm/degrees C for the nondefect fiber). The 16% to 70% relative difference between the thermal coefficients of the two fibers, together with their similar strain sensitivity enables the simultaneous measurement of strain and temperature.

Abstract
Two Fabry-Perot interferometers based on chemical etching in multimode graded index fibers are fabricated and their response to temperature and strain are compared. Chemical etching is applied in the graded index fiber end creating an air cavity. The interferometric cavity is formed when the graded index fiber with the air concavity is spliced to a single-mode fiber. The intrinsic sensors present high sensitivity to strain and low sensitivity to temperature. For the 62.5 mu m core fiber, sensitivities of 6.99 pm/mu epsilon and, 0.95 pm/degrees C were obtained for strain and temperature, respectively. The sensor based in the 50 mu m core fiber, on the other hand, presented sensitivities of 4.06 pm/mu epsilon and -0.84 pm/degrees C for strain and temperature, respectively.