Abstract
A sensor based on the fiber Bragg grating (FBG) and additive manufacturing for diameter variation measurement is proposed and experimentally demonstrated in this work. Two designs were proposed: a FBG alone and a FBG in series with a spring. Three tests were developed for each design, and at the end, the statistical treatment was performed. The designs were fabricated using a 3D printer, and the FBG sensor is embedded. The results demonstrated that the structures proposed in this work can be used to monitor diameter variation, among other applications. The sensors, with and without spring in series, presented sensitivities of 0.0671 nm/mm and 0.5116 nm/mm, respectively, with a good linear response greater than 0.99.

Abstract
A refractive index sensor was designed using a novel approach to sensing based on a cleaved standard fiber Bragg grating (FBG) at the grating region, which enables the FBG to interact with its surrounding environment. The sliced-FBG (SFBG) exhibits a variable phase shift in the reflection response due to the length of the last grating's pitch, which differs from the rest. At the SFBG, the signal is the result of interference between the reflected wave from the grating and the transmitted spectrum returned due to Fresnel reflection at the final pitch, and the intensity of this signal depends on the refractive index of the surrounding medium. Based on this phenomenon, an intensity-based refractive index sensor with self- referencing technique was employed in this experiment, whereby the grating peak maximum point served as the signal reference, while the minimum of the Fresnel peak from each measurement functioned as the signal input. The proposed sensor demonstrated the ability to measure refractive indices within the range of 1.333-1.339, with a resolution of approximate to 10(-3), and a minimum detectable value of 6x10(-4) RIU (the data yielded a linear response with R-2=0.990). This study presents an innovative data sensing approach compared to existing techniques found in literature, which typically employ wavelength variation in the reflected wave to extract the desired information.

Abstract
This work analyzes the sensitivity of an optical system consisting of two fiber Fabry-Perot ( FP) interferometers and the apparent increase in sensitivity due to the harmonics of the Vernier effect. Two scenarios are examined: (1) when the larger FP cavity acts as the sensor, and (2) when the smaller FP cavity acts as the sensor. The computation analysis reveals that in the first scenario, higher-order spectral harmonics yield greater sensitivity for maxima and minima of the same order. In the second scenario, however, the sensitivity remains constant and does not depend on the harmonic order. Moreover, it is demonstrated that the sensitivity curve is identical for both scenarios, regardless of the harmonic order. This outcome occurs because the use of spectral harmonics simply reduces the free-spectral range in certain situations, bringing the extrema closer to the maximum sensitivity condition (i.e., Delta L = 0) and thereby increasing sensitivity. Consequently, if points on the envelope other than maxima or minima are used, the sensitivity achieved is the same for both scenarios.

Abstract
In this letter, we propose a method for utilizing the internal cavities of optical circulator devices-commonly referred to as parasitic cavities-as optical reference cavities. The method involves using an optical circulator operating at 1550 nm, illuminated by a light source at 1330 nm, thereby enhancing the amplitude of the interferometric signals generated by the internal optical cavities. The system was characterized by using both an Optical Spectrum Analyzer (OSA) and the Low-Coherence Interferometry (LCI) technique. Experimental results indicate that the Optical Path Difference (OPD) remains constant with varying aperture sizes, thereby confirming the feasibility of employing the optical circulator as a reference sensor. Finally, its performance as a reference sensor is demonstrated through its integration with an external cavity that functions as a displacement sensor.

Abstract
Polarization-based fiber sensors rely on the dynamics of the Stokes vector at the output of the optical fiber to probe stimuli that induce polarization variations. However, these sensors often suffer from limitations in sensitivity, precision, and reproducibility. In this work, we address these challenges by incorporating concepts from the Mueller matrix formalism to enhance the capabilities of such sensors. Specifically, we measure the Mueller matrix in the polarization basis that describes how the polarization evolves inside the optical fiber. Leveraging this formalism, we configure the system as a precise sensor to detect deformations along the fiber. By utilizing the Fisher Information framework, we significantly improve accuracy and resolution, enabling the detection of subtle perturbations with greater precision. This study introduces a novel approach for precise polarization control and advanced fiber-based sensing applications.

Abstract
In this study, we demonstrate the measurement of electric power using an optical ground wire ( OPGW). The tests were conducted on an OPGW cable from a high-voltage transmission line in Sines, Portugal, operating at 400 kV. A buried fiber position, free of 50 Hz and 100 Hz frequency interference, was selected to confirm that the 50 Hz frequency is not due to mechanical perturbation or electronic noise. Additionally, two suspended fiber positions (at 2500 m and 8500 m), where these frequencies were clearly observed, were analyzed. This study also examined the positioning of poles and splice detection between cables.