Abstract
The excitation of two different electromagnetic surface waves-surface plasmon polaritons (SPPs) and Bloch surface waves (BSWs)-is demonstrated in a 1-D metal-dielectric photonic crystal with numerical and experimental studies. The discussed structure consists of an Ag-TiO2 thin-film stack forming a metal-insulator-metal-insulator device. The thickness of the TiO2 layer placed between the metals is tested for two different values (50 and 300 nm), which also allows the excitation of guided-mode resonances. It is observed that BSWs in this metal-dielectric structure behave similar to the case of all-dielectric photonic crystals, whereas the SPP modes display similar properties to those excited in metal-insulator-metal cavities. The sensitivity of these surface states to variations in the refractive index (RI) of the external dielectric is characterized. For the case of the plasmonic modes, a maximum sensitivity of (7.2 +/- 0.3) x 10(3) nm/RIU was measured, while for the BSW the maximum sensitivity was (1.20 +/- 0.05) x 10(2) nm/RIU. Due to the large field enhancement and penetration on external media, these surface states display exceptional properties for application in optical sensors, and the presented results provide interesting possibilities in the design of novel sensing structures with a flexible selection of surface states for interrogation.

Abstract
Continuous monitoring of hydrogen (H2) concentration is critical for safer use, which can be done using optical sensors. Palladium (Pd) is the most commonly used transducer material for this monitoring. This material absorbs H2 leading to an isotropic expansion. This process is reversible but is affected by the interaction with interferents, and the lifetime of Pd thin films is a recurring issue. Fiber Bragg Grating (FBG) sensors are used to follow the strain induced by H2 on Pd thin films. In this work, it is studied the stability of Pd-coated FBGs, protected with a thin Polytetrafluoroethylene (PTFE) layer, 10 years after their deposition to assess their viability to be used as H2 sensors for long periods of time. It was found that Pd coatings that were PTFE-protected after deposition had a longer lifetime than unprotected films, with the same sensitivities that they had immediately after their deposition, namely 23 and 10 pm/vol% for the sensors with 150 and 100 nm of Pd, respectively, and a saturation point around 2 kPa. Furthermore, the Pd expansion was analyzed in the presence of H2, nitrogen (N2), carbon dioxide (CO2), methane (CH4) and water vapor (H2O), finding that H2O is the main interferent. Finally, an exhaustive test for 90 h is also done to analyze the long-term stability of Pd films in dry and humid environments, with only the protected sensor maintaining the long-term response. As a result, this study emphasizes the importance of using protective polymeric layers in Pd films to achieve the five-year lifetime required for a real H2 monitoring application.

Abstract
The gut microbiome is shaped early in life by dietary and lifestyle factors. Specific compounds in the gut affect the growth of different bacterial species and the production of beneficial or harmful byproducts. Dysbiosis of the gut microbiome has been linked to various diseases resulting from the presence of harmful bacteria and their byproducts. Existing methods for detecting microbial species, such as microscopic observation and molecular biological techniques, are costly, labor-intensive, and require skilled personnel. Biosensors, which integrate a recognition element, transducer, amplifier, signal processor, and display unit, can convert biological events into electronic signals. This review provides a comprehensive and systematic survey of scientific publications from 2018 to June 2024, obtained from ScienceDirect, PubMed, and Scopus databases. The aim was to evaluate the current state-of-the-art and identify knowledge gaps in the application of aptamer biosensors for the determination of gut microbiota. A total of 13 eligible publications were categorized based on the type of study: those using microbial bioreceptors (category 1) and those using aptamer bioreceptors (category 2) for the determination of gut microbiota. Point-of-care biosensors are being developed to monitor changes in metabolites that may lead to disease. They are well-suited for use in the healthcare system and offer an excellent alternative to traditional methods. Aptamers are gaining attention due to their stability, specificity, scalability, reproducibility, low production cost, and low immunogenicity. While there is limited research on using aptamers to detect human gut microbiota, they show promise for providing accurate, robust, and cost-effective diagnostic methods for monitoring the gut microbiome.

Abstract
Laser-induced breakdown spectroscopy allows fast and versatile elemental analysis, standing as a promising technique for a wide range of applications both at the research and industry levels. Yet, its high operation speed comes with a high throughput of data, which introduces some challenges at the level of the data processing domain, mainly due to the large computational load and data volume. In this work, we analyze and discuss opportunities of distributed computing paradigms and resources to address some of these challenges, covering most of the procedures usually employed in typical applications. We infer the possible impact of such computing resources by presenting some metrics of simple processing prototypes running in state-of-the-art computing facilities. Our results allow us to conclude that, while underexplored so far, these computing resources may allow for the development of tools for timely research and analysis in demanding applications and introduce novel solutions toward a more agile working environment.

Abstract
This communication explores an optical extreme learning architecture to unravel the impact of using a nonlinear optical media as an activation layer. Our analysis encloses the evaluation of multiple parameters, with special emphasis on the efficiency of the training process, the dimensionality of the output space, and computing performance across tasks associated with the classification in low-dimensionality input feature spaces. The results enclosed provide evidence of the importance of the nonlinear media as a building block of an optical extreme learning machine, effectively increasing the size of the output space, the accuracy, and the generalization performances. These findings may constitute a step to support future research on the field, specifically targeting the development of robust general-purpose all-optical hardware to a full-stack integration with optical sensing devices toward edge computing solutions.

Abstract
Lately, the field of optical computing resurfaced with the demonstration of a series of novel photonic neuromorphic schemes for autonomous and inline data processing promising parallel and light-speed computing. We emphasize the Photonic Extreme Learning Machine (PELM) as a versatile configuration exploring the randomness of optical media and device production to bypass the training of the hidden layer. Nevertheless, the implementation of this framework is limited to having the output layer performed digitally. In this work, we extend the general PELM implementation to an all-optical configuration by exploring the amplitude modulation from a spatial light modulator (SLM) as an output linear layer with the main challenge residing in the training of the output weights. The proposed solution explores the package pyTorch to train a digital twin using gradient descent back-propagation. The trained model is then transposed to the SLM performing the linear output layer. We showcase this methodology by solving a two-class classification problem where the total intensity reaching the camera predicts the class of the input sample.