Cookies
O website necessita de alguns cookies e outros recursos semelhantes para funcionar. Caso o permita, o INESC TEC irá utilizar cookies para recolher dados sobre as suas visitas, contribuindo, assim, para estatísticas agregadas que permitem melhorar o nosso serviço. Ver mais
Aceitar Rejeitar
  • Menu
Publicações

Publicações por Paulo Vicente Marques

2019

Spectral characteristics of optical waveguides fabricated in glass by femtosecond laser direct writing

Autores
Amorim, VA; Viveiros, D; Maia, JM; Marques, PVS;

Publicação
FOURTH INTERNATIONAL CONFERENCE ON APPLICATIONS OF OPTICS AND PHOTONICS

Abstract
The fabrication of optical waveguides with femtosecond laser direct writing is reported in two materials, Suprasil1 and Eagle2000. The influence of typical fabrication parameters, such as pulse energy and scan velocity, on the waveguide's spectral characteristics is explored from 500 to 1700 nm. Tests conducted in Suprasil1 evidence a strong presence of Rayleigh scattering, hindering the production of low-loss waveguides at short wavelengths. On the other hand, optical waveguides fabricated in Eagle2000 exhibited lower insertion losses at short wavelengths, enabling the fabrication of low-loss broadband optical waveguides with a two order of magnitude higher scan velocity when compared with Suprasil1.

2019

Femtosecond Laser Micromachining of Fabry-Perot Interferometers in Fused Silica for Refractive Index Sensing

Autores
Maia, JM; Amorim, VA; Viveiros, D; Marques, PVS;

Publicação
FOURTH INTERNATIONAL CONFERENCE ON APPLICATIONS OF OPTICS AND PHOTONICS

Abstract
A Fabry-Perot interferometer was fabricated inside a fused silica substrate through femtosecond laser micromachining. The influence of the waveguide's writing parameters on the measured signal's quality was studied for an interferometer with a 27-mu m wide cavity. Optimal signal-to-noise ratio and fringe visibility were obtained for waveguides written at 75 nJ and 50 mu m/s. The same device was characterized with different refractive index liquids, and a maximum sensitivity of 1181.4 +/- 23.6 nm/RIU was obtained in the index range of 1.2962 to 1.3828 (at 1550 nm) for the spectral order m = 46.

2019

Mass Producible Low-Loss Broadband Optical Waveguides in Eagle2000 by Femtosecond Laser Writing

Autores
Amorim, VA; Viveiros, D; Maia, JM; Marques, PVS;

Publicação
IEEE PHOTONICS TECHNOLOGY LETTERS

Abstract
Optical waveguides were fabricated in alkaline earth boro-aluminosilicate glass, by femtosecond laser direct writing, with varying pulse energy and scan velocity. A spectral characterization, from 500 nm to 1700 nm, was made in order to determine their losses and understand its dependence on the processing parameters. Three major loss mechanisms were identified. At longer wavelengths, loss is mainly due to weak coupling. On the other hand, the behavior at shorter wavelengths is governed by propagation loss due to Rayleigh scattering, which was shown to be practically eliminated (& x003C; 0.05 dB $\cdot$ cm $<^>{-1} {\cdot }\,\,\mu \text{m}<^>{4}$ ) at higher scan velocities. Bulk absorption was also found to have an influence in the propagation losses at higher wavelengths. The combination of intermediate pulse energies (between 125-250 nJ) and high scan velocities (above 6 cm/s) allowed the fabrication of optical waveguides offering low losses across the entire range of wavelengths tested, facilitating applications that require larger wavelength working bands. Furthermore, since optimal fabrication conditions are achieved at higher scanning velocities, mass production with reduced fabrication times can be achieved.

2019

3D prototyping of a fiber Bragg grating vibration sensor for power transformers

Autores
Monteiro, CS; Viveiros, D; Linhares, C; Tavares, SMO; Mendes, H; Silva, SO; Marques, PVS; Frazao, O;

Publicação
FOURTH INTERNATIONAL CONFERENCE ON APPLICATIONS OF OPTICS AND PHOTONICS

Abstract
In this work, 3D printing is explored as a solution for fast prototyping of optical fiber sensors with applications in power transformers. Two different sensing structures were evaluated using finite element method (FEM) analysis and were fabricated using 3D printing. The printed structures are composed by acrylonitrile butadiene styrene (ABS), a common thermoplastic polymer used in 3D printing. Attaching a fiber Bragg grating (FBG) to each structure, frequency measurements were successfully obtained for values between 20 and 250 Hz.

2019

Fabrication of periodic structures in optical fibers by femtosecond laser micromachining for sensing applications

Autores
Viveiros, D; Maia, JM; Amorim, VA; Jorge, PAS; Marques, PVS;

Publicação
FOURTH INTERNATIONAL CONFERENCE ON APPLICATIONS OF OPTICS AND PHOTONICS

Abstract
A femtosecond laser direct writing system was developed to explore the fabrication of periodic structures in optical fibers. The possibility to write type I first- and second-order Bragg gratings in the same single-mode fiber (SMF-28e), with reflectivities of 99.6 % and 59.3 %, respectively, is presented. The fabrication of structures (waveguides and grating) in a coreless and in a SMF-28e fiber was first demonstrated, and the gratings were then exposed to a thermal annealing up to 1000 degrees C. The FBG inscribed in the SMF-28e fiber presents thermal stability at temperatures of 800 degrees C and a temperature sensitivity of 14.34 pm/degrees C was determined.

2019

FBG two-dimensional vibration sensor for power transformers

Autores
Monteiro, CS; Vaz, A; Viveiros, D; Linhares, C; Tavares, SMO; Mendes, H; Silva, SO; Marques, PVS; Frazao, O;

Publicação
SEVENTH EUROPEAN WORKSHOP ON OPTICAL FIBRE SENSORS (EWOFS 2019)

Abstract
Power transformers are at the core of power transmission systems. The occurrence of system failure in power transformers can lead to damage of adjacent equipment and cause service disruptions. Structural and electrical integrity assessment in real time is of utter importance. Conventional techniques, typically electrical sensors or chemical analysis, present major drawbacks for real-time measurements due to high electromagnetic interference or for being time-consuming. Optical fiber sensors can be used in power transformers, as they are compact and immune to electromagnetic interferences. In this work, an optical fiber sensor composed by 2 fiber Bragg gratings, attached in a cantilever structure was explored. The prototype was developed with a 3D printer using a typical filament (ABS) that enable a fast and low-cost prototyping. The response of the sensor to vibration was tested using two different vibration axes for frequencies between 10 and 500 Hz. Oil compatibility was also studied using thermal aging and electrical tests. The studies shown that ABS is compatible with the power transformer mineral oil, but the high working temperatures may lead to material creeping, resulting in permanent structural deformation.

  • 4
  • 24