Abstract
Two new configurations of high-birefringent fiber loop mirror with an output port probe are proposed. The two configurations used two couplers spliced between them with unbalanced arms and one output port is used as the probe sensor. The difference between them is that the section length of high-birefringent fiber is located between the two couplers (first configuration) or spliced in the output port probe (second configuration). The first new configuration is studied as an optical refractometer and the second configuration is analyzed when the strain and temperature are applied.

Abstract

Abstract
In this work, we analyze a remote optical sensor system composed of two Fiber Bragg Gratings (FBGs) and one Long Period Grading (LPG) capable of simultaneously sensing the temperature and the refractive index, separated by 50 km from the optical source and the interrogation unit. Since the active components of the system and the sensor head are separated over such a large distance, it is necessary to consider Raman amplification o strengthen the optical signal. We present both experimental measurements and the results of numerical simulations, which describe the signal evolution and predict the measurement results for a remote sensor based on a LPG. The simulation codes are also used to study a hybrid sensor composed of two FBGs with a LPG. We show that the power ratio between the two central wavelengths of the FBG has a linear relation with the change of refractive index of the sensored medium.

Abstract
A single-mode nonadiabatic tapered optical fiber (NATOF) sensor was inserted into a fiber loop mirror (FLM) enabling us to tune its sensitivity towards refractive index (RI). The NATOF was fabricated by the heat pulling method, utilizing a CO laser. The adjustment of the polarization controllers (PCs) inserted in loop allowed us to excite different cladding modes in the interferometric taper resulting in different optical paths for the clockwise and the counterclockwise beams. By variation of the PCs' settings, the sensitivity of the sensor for RI in the range from 1.3380 to 1.3510 could be tuned from 876.24 to 1233.07 nm/RIU. Experimental results show that the sensitivity to the external RI increased with the order of the cladding mode.

Abstract
Cyanobacteria deteriorate the water quality and are responsible for emerging outbreaks and epidemics causing harmful diseases in Humans and animals because of their toxins. Microcystin-LR (MCT) is one of the most relevant cyanotoxin, being the most widely studied hepatotoxin. For safety purposes, the World Health Organization recommends a maximum value of 1 mu g L(-1) of MCT in drinking water. Therefore, there is a great demand for remote and real-time sensing techniques to detect and quantify MCT. In this work a Fabry-Perot sensing probe based on an optical fibre tip coated with a MCT selective thin film is presented. The membranes were developed by imprinting MCT in a sol-gel matrix that was applied over the tip of the fibre by dip coating. The imprinting effect was obtained by curing the sol-gel membrane, prepared with (3-aminopropyl) trimethoxysilane (APTMS), diphenyl-dimethoxysilane (DPDMS), tetraethoxysilane (TEOS), in the presence of MCT. The imprinting effect was tested by preparing a similar membrane without template. In general, the fibre Fabry-Perot with a Molecular Imprinted Polymer (MIP) sensor showed low thermal effect, thus avoiding the need of temperature control in field applications. It presented a linear response to MCT concentration within 0.3-1.4 mu g L(-1) with a sensitivity of -12.4 +/- 0.7 nm L mu g(-1). The corresponding Non-Imprinted Polymer (NIP) displayed linear behaviour for the same MCT concentration range, but with much less sensitivity, of -5.9 +/- 0.2 nm L mu g(-1). The method shows excellent selectivity for MCT against other species co-existing with the analyte in environmental waters. It was successfully applied to the determination of MCT in contaminated samples. The main advantages of the proposed optical sensor include high sensitivity and specificity, low-cost, robustness, easy preparation and preservation.

Abstract
A technique for the fabrication of luminescence-based fiber-optic optrodes with multiple analyte sensitivity is proposed. Combination of photosensitive polymers doped with different luminescent indicators enabled the production of fiber probes, by self-guiding photo-polymerization, with different geometries and sensing capabilities. Results demonstrating the method flexibility are shown with luminescent probes doped with CdSe/ZnS quantum dots and an organometalic ruthenium complex for simultaneous detection of oxygen and temperature.