José Ribeiro

Abstract
The ability to assess molecular binding kinetics in real time is critical for advancing our understanding of molecular interactions in biochemical and biotechnological systems. This work presents a novel optical tweezer (OT)-based method to monitor molecular affinity in real time, focusing on the high-affinity streptavidin-biotin system as a model. Transparent poly(methyl methacrylate) (PMMA) microparticles functionalized with streptavidin were trapped before, during, and after binding with biotinylated bovine serum albumin (biotin-BSA), enabling the analysis of forward-scattered signals to detect nanoscale changes in particle size. By applying the Power Spectral Density method, the friction coefficient of individual particles was calculated, allowing for real-time tracking of binding dynamics and the estimation of the association rate constant (kon approximate to 106M-1s-1). These results are consistent with literature values and demonstrate the potential of this OT-based approach for non-invasive, label-free detection of molecular interactions. Compared to existing techniques, such as atomic force microscopy and cantilever-based sensors, this method offers significant advantages, including real-time monitoring, adaptability to different bioaffinity systems, and compatibility with miniaturized setups. This work establishes a foundation for using OT-based tools to monitor high-affinity molecular interactions in real time. While demonstrated here using biotinylated BSA as a model ligand, future studies will explore the method's applicability to smaller ligands and more subtle surface modifications.

Abstract
Haemoglobin (Hb) concentration is a key biomarker for several diseases. Traditional laboratory methods often have limitations due to their time-consuming nature, the need for skilled personnel, or the use of high-cost instrumentation. This work presents a sensing strategy for developing new point-of-care tests (POCTs) for Hb detection via a proof of concept. The proposed sensing approach is implemented using plasmonic plastic optical fiber (POF) sensor chips that integrate an electropolymerized molecularly imprinted polymer (eMIP) film on the plasmonic surface for Hb-selective detection. The developed sensor system demonstrates an ultra-low detection limit of 80 fM in buffer, about five orders of magnitude lower than that of other comparable Hb sensors. Selectivity tests against common interfering proteins, such as bovine serum albumin (BSA) and immunoglobulin G (IgG), confirmed high specificity towards the target analyte. Moreover, the sensor’s performance was tested using a whole-blood sample, yielding results consistent with those of standard haematology analysis. The proposed sensor system, based on simple equipment, provides a quick (about 10 min) and cost-effective (about 10 euros per chip) label-free diagnostic tool for POCTs in real-world scenarios, such as finger-prick sampling, offering a less invasive alternative to traditional laboratory methods, towards devices useful for Internet of Medical Things (IoMT).

Abstract
The development of simple, selective, and cost-effective methods for quantification of bovine serum albumin (BSA) is currently very important for assessing milk quality (and safety). In this work, a new surface plasmon resonance (SPR) sensor was developed, consisting of imprinted hydrogel-based nanoparticles (nanoMIPs) immobilized on gold platforms, to quantify BSA in bovine milk. The nanoMIPs prepared for recognition of BSA were synthesized by the precipitation polymerization approach, using a synthetic BSA epitope (VVSTQTALA) as template. The spherical MIP nanoparticles (NPs) had an average size of 60 nm. The binding studies performed revealed that the binding affinity of the prepared nanoMIPs to BSA (KD = 7.1 × 10-6 mol L-1) was comparable to that obtained by a natural BSA antibody (KD = 2.5 × 10-6 mol L-1). The plasmonic sensor incorporating the MIP nanomaterials achieved a limit of detection (LOD) of 1.02 × 10-6 mol L-1 (0.068 mg mL-1) and a limit of quantification (LOQ) of 3.39 × 10-6 mol L-1 (0.225 mg mL-1), over a linear range from 2.0 × 10-6 mol L-1 to 1.5 × 10-5 mol L-1. Moreover, the selectivity studies revealed a significant sensor response towards casein and a negligible response towards vancomycin. In the end, the optical sensor was tested against commercial milk samples, showing promising viability for detection of BSA as the value reported by the plasmonic sensor ((1.0 ± 0.1) × 10-4 mol L-1) was very close to that obtained by size exclusion-high-performance liquid chromatography (SEC-HPLC). © 2025 The Author(s)

Abstract

Abstract
Hydroponics is an advanced agricultural technique that involves growing plants without soil. Instead, plants are cultivated in a nutrient-rich water solution that provides all the essential minerals they need to thrive, allowing plants to grow either with their roots directly in the solution or supported by inert substrates like pine bark, coconut husk fiber, and rice husk. The solid waste generated from hydroponic cultivation is valuable due to its low cost, abundance, biodegradability, and renewability. These residues are rich in lignocellulosic materials, which can be extracted and refined to produce cellulose and nanocellulose (NC). In this work, cellulose and nanocellulose were extracted from residues of coconut husk fiber and a mixture of pine bark and coconut husk fiber, used in tomato and strawberry hydroponics, respectively. The residues were ground, washed, and chemically treated to obtain cellulose and NC. The chemical process involved several stages: (i) acid treatment, alkaline treatment, and bleaching to isolate cellulose, and (ii) acid hydrolysis followed by ultrasonication to obtain NC. Both materials underwent characterization using various techniques such as TGA, DSC, XRD and FTIR-ATR, which confirmed very low levels of lignin and hemicellulose. Morphological characterization through SEM revealed the presence of micro- and nano-crystals in the cellulose and NC samples, respectively, highlighting the effectiveness of the extraction method. The high purity and quality of the extracted materials make them competitive with commercially available products, suitable for applications in healthcare, food packaging, and automotive industries, while supporting recycling and reuse principles.