Abstract
Over the past 18 months, we have performed hundreds of temperature characterizations of fiber Bragg gratings inscribed in different germanium-doped silica glass fibers. Under experimental conditions, the main conclusions are as follows: the temperature dependence of the temperature gauge factor or the normalized temperature sensitivity, K-T, was found to be quadratic in the -50-200 degrees C range, while it may be considered linear for the -20-100 degrees C range; K-T values at 20 degrees C vary from 5.176 x 10(-6) K-1, for a B/Ge co-doped fiber up to 6.724 x 10(-6) K-1, for a highly Ge-doped fiber; K-T does not depend on the hydrogen-loading process or the gratings coupling strength; K-T is essentially independent of wavelength in the 1500-1600 nm range, its value being accurately determined with a relative error similar to 0.2%; based on the accurate value of K-T = 6.165 x 10(-6) K-1, at 20 degrees C, obtained for gratings inscribed in the SMF-28 fiber, we calculated a value of 19.4 x 10(-6) K-1 for the thermo-optic coefficient of bulk germanium glass; and gratings produced by femtosecond-laser radiation and UV-laser radiation exhibit comparable values of K-T. The previous achievements allow, by having knowledge of K-T for a single grating, the accurate determination of the temperature dependence of the Bragg wavelength for any other grating inscribed in the same fiber; the presented methodology enables one to determine the unknown gratings' temperature sensitivity, typically with an error of 0.01 pm/degrees C, being, therefore, very useful in research labs and computer simulations. Thus, expressions for the temperature dependence of K-T for gratings inscribed in several fibers are given, as well as an expression for K-T as a function of the effective refractive index. We have also fully analyzed the potential sources of error in K-T determination.

Abstract
In this paper we present results on the normalized temperature sensitivity of UV- and fs-induced fiber Bragg gratings in a singlemode fiber with similar to 4.7 mol% GeO2 and having an Ormocer coating. In the 1500-1600 nm wavelength range, the former shows an almost constant value of 6.165x10(-6) K-1, whilst the fs-induced present some variation not related with the strength of the grating but probably due to induced birefringence. The average value obtained was 6.191x10(-6) K-1 which is higher than the former. For the UV-induced gratings in the Corning SMF-28 fiber (3.67 mol% GeO2) the value obtained was 6.143x10(-6) K-1. The achieved values are compatible with the use of Corning 7980 silica-based cladding fiber. Preliminary results also show no measurable impact of the hydrogenation process or the strength of the grating on the normalized temperature sensitivity.

Abstract
A semi-distributed optical fiber bending extensometer system based on OTDR is proposed, consisting of N-loops designed to enable different maximum extension measurements and sensitivities. This system offers a low-cost solution for monitoring landslides and similar civil structures. Tests conducted at 1625 nm demonstrate that different series of sensors can be independently measured with elongation errors typically within +/- 0.25 cm across a range from 0 to 9 cm.

Abstract
A flexible wearable sensor utilizing a balloon-shaped interferometer structure, created from a bent standard single-mode fiber and a 3D-printed piece, was introduced and shown for respiratory monitoring. The interferometer is a compact, cost-effective, and easily fabricated sensor. The fiber's curvature causes interference between the core and cladding modes, which in turn results in the sensor operation. In the balloon-shaped curving section, light traversing the core partially escapes and interacts with the cladding. The preliminary results demonstrate an average displacement of 9.3 nm and the capability to evaluate breathing rate.

Abstract
A sensor based on the fiber Bragg grating (FBG) and additive manufacturing for diameter variation measurement is proposed and experimentally demonstrated in this work. Two designs were proposed: a FBG alone and a FBG in series with a spring. Three tests were developed for each design, and at the end, the statistical treatment was performed. The designs were fabricated using a 3D printer, and the FBG sensor is embedded. The results demonstrated that the structures proposed in this work can be used to monitor diameter variation, among other applications. The sensors, with and without spring in series, presented sensitivities of 0.0671 nm/mm and 0.5116 nm/mm, respectively, with a good linear response greater than 0.99.