Abstract
Optical fibre sensors for Hydrogen detection at low concentrations has become a growing research area using Palladium as an active medium. Palladium is widely used in hydrogen sensing as it show a high and selective affinity for hydrogen. This metal is capable to absorb hydrogen up to 900 times its own volume which permits that during the expansion mechanical forces are applied in the fibre modifying the optical response. Several optical fibre hydrogen sensor heads coated with Palladium are presented and compared using different working principles: interferometric, intensity and fiber grating-based sensors. These principles were applied in Fabry-Perot cavities, fibre Bragg gratings written in fibre SMF28 with etching in the cladding, multimode interferometers and fibre end micro-mirrors. Palladium thin film coatings over the fibre surface and with thicknesses from 10nm to 350nm were produced by using the sputtering RF technique. These studies were performed in a Hydrogen/Nitrogen atmosphere with Hydrogen concentrations from 0% to 4% (lower limit explosion). The Bragg grating inscribed in a fibre with reduced cladding diameter appears to be one of the best approaches for a fibre optic sensing head for Hydrogen detection. Future work will continue the investigation of other fibre optic structures with Hydrogen sensing capabilities and their application in specific field situations will be assessed.

Abstract
An optical fiber sensor based on a tapered-FBG coated with 150 nm-thick Pd film is proposed for hydrogen pressure detection. The FBG was written in a 50 µm-diameter tapered fiber by DUV femtosecond laser technology. A second FBG was inscribed in the untapered fiber region for temperature compensation. The sensing head was able to detect the variation of hydrogen pressure in the range 0-780 kPa and a maximum sensitivity of 0.15 pm/kPa was achieved. © 2012 OSA.

Abstract
It is reported a new dynamic electrical interrogation technique based on the modulation of two Bragg gratings structures located in the readout unit that permits to attenuate the effect of the 1/f noise of the electronics in the resolution of the LPG-based curvature sensors. The new concept is tested to detect large variations of curvature being achieved a resolution of 6.56 × 10-3 meters.

Abstract
The interrogation of optical fiber sensors (OFS) often relies on complex devices such as optical spectrum analyzers (OSAs) that are expensive with low portability and mainly suited to laboratory measurements or dedicated interrogation systems with limited spectral range. An interrogation unit was designed and fabricated using a photodetector combined with a micro-electromechanical system and a Fabry-Perot interferometer (MEMS-FPI) working as a tunable filter with a response in the range 1350-1650 nm. Deconvolution techniques were applied to mitigate the effect of the broadband response of the tunable filter on the measured signal. The performance of the unit was validated with the interrogation of long-period fiber gratings (LPFGs) as temperature, refractive index (RI), and relative humidity (RH) sensors. For the temperature, a sensitivity of 0.135 +/- 0.007 nm/degrees C was obtained, which showed a 4.9% relative error when compared to the same measurement with an OSA. For the RI, a sensitivity of 147 +/- 11 nm/RIU was obtained, which showed a relative error lower than 1% when compared to the OSA. For the humidity, sensitivities of 0.742 +/- 0.005 and 0.056 +/- 0.006 nm/%RH were obtained, with errors of 2.75% and 6.67%, respectively, when compared to a commercial dedicated interrogation system. The low relative error obtained when compared to commercial alternatives shows the potential of the system to be used in real-time applications that require portability, low cost, energy efficiency, and capacity for integration in dedicated systems.

Abstract
The sensitivity of one-dimensional Bloch surface wave (BSW) sensors to external refractive index variations using Kretschmann's configuration is calculated analytically by employing first-order perturbation theory for both TE and TM modes. This approach is then validated by com- parison with both transfer matrix method simulations and experimental results for a chosen photonic crystal structure. Experimental sensitivities of (8.4 +/- 0.2)x102 and (8.4 +/- 0.4)x102 nm/RIU were obtained for the TE and TM BSW modes, corresponding to errors of 0.02% and 4%, respectively, when comparing with the perturbation the- ory approach. These results provide interesting insights into photonic crystal design for Bloch surface wave sensing by casting light into the important parameters related with sen- sor performance.(c) 2023 Optica Publishing Group

Abstract
Water vapor sorption is a powerful tool for the analysis of cement paste, one of the most used substances by mankind. The monitoring of cementitious materials is fundamental for the improvement of infrastructure resilience, which has a deep impact on the economy, the environment, and on society. In this work, a multimode fiber was embedded in cement paste for real-time monitoring of cement paste water vapor sorption. Changes in the reflected light intensity due to the build-up of water in the cement paste's pores were exploited for this purpose. The sample was 7-day moist cured, and the relative humidity was controlled between 8.9% and 97.6%. Reflected light intensity was converted into a specific surface area of cement paste (133 m(2)/g) and thickness of water through the Brunauer-Emmett-Teller (BET) method and into a pore size distribution through the Barret-Joyner-Halenda (BJH) method. The results achieved through reflected light intensity agree with those found in the literature, validating the usage of this setup for the monitoring of water vapor sorption, breaking away from standard gravimetric measurements.