Abstract
The spectral behavior in the C-band of fiber Bragg gratings (FBGs) was analyzed as a function of temperature and strain. The FBGs were fabricated in pure silica four-leaf-clover- shaped suspended-core fibers by (DUV) femtosecond laser exposure (3.6 W at 800 nm, 130 fs, 1 kHz frequency tripled to 350 fs, 650 mW at 267 nm). A defect fiber (with a hollow hole in the core) and nondefect fiber were compared both yielding approximate to 1 pm/mu epsilon sensitivity to strain but different sensitivity to temperature (from 3.0 pm/degrees C to 8.4 pm/degrees C for the defect fiber and 10 pm/degrees C for the nondefect fiber). The 16% to 70% relative difference between the thermal coefficients of the two fibers, together with their similar strain sensitivity enables the simultaneous measurement of strain and temperature.

Abstract
Two new configurations of high-birefringent fiber loop mirror with an output port probe are proposed. The two configurations used two couplers spliced between them with unbalanced arms and one output port is used as the probe sensor. The difference between them is that the section length of high-birefringent fiber is located between the two couplers (first new configuration) or spliced in the output port probe (second new configuration). The second new configuration presents great advantage, especially for remote sensing using only one fiber to the sensing head. The two new configurations were compared with the conventional high-birefringent fiber loop mirror when strain is applied and showed similar sensitivities. The first new configuration is studied as an optical refractometer.

Abstract
In this letter, interferometric sensors based on antiresonance reflecting optical waveguide (ARROW) fibers were developed, and used to sense strain and temperature. Two types of solid-ore ARROW fibers were considered and signal demodulation was achieved by using the white light interferometric technique. The ARROW fibers have two rings of high index rods arranged in a hexagonal structure with a lattice constant of 6 m. The different sizes of the rods cause different measurand sensitivities for the two fibers. Resolutions of +/- 1.1 mu epsilon and +/- 0.07 degrees C were achieved for strain and temperature, respectively.

Abstract
Two Fabry-Perot interferometers based on chemical etching in multimode graded index fibers are fabricated and their response to temperature and strain are compared. Chemical etching is applied in the graded index fiber end creating an air cavity. The interferometric cavity is formed when the graded index fiber with the air concavity is spliced to a single-mode fiber. The intrinsic sensors present high sensitivity to strain and low sensitivity to temperature. For the 62.5 mu m core fiber, sensitivities of 6.99 pm/mu epsilon and, 0.95 pm/degrees C were obtained for strain and temperature, respectively. The sensor based in the 50 mu m core fiber, on the other hand, presented sensitivities of 4.06 pm/mu epsilon and -0.84 pm/degrees C for strain and temperature, respectively.

Abstract
A compact fiber-optic inclinometer based on a fiber-taper Michelson interferometric sensor is constructed and demonstrated. The sensor consist of a single symmetrically taper waist of 80 mu m distanced 30 mm from the single-mode fiber end-tip right-angled cleaved. The amplitude of the bending angle of the fiber taper interferometer is obtained by passive interferometric interrogation based on the generation of two quadrature phase-shifted signals from two fiber Bragg gratings with different resonant wavelengths. Optical phase-to-bending sensitivity of similar to 1.13 rad/degree and a bend angle resolution of similar to 0.014 degree/root Hz were achieved.

Abstract
A sensing head based on two fiber Bragg gratings arranged in a twisted configuration is proposed to measure three parameters simultaneously, namely 1) temperature, 2) strain, and 3) transverse load. One of the gratings is impressed into a high-birefringence fiber that provides two distinct spectral signatures, which, together with the signature of the second grating and the geometric characteristics of the sensing head, enable the degrees of freedom required to achieve the simultaneous measurement functionality. The resolutions achieved with this configuration for the measurement of temperature, strain, and transverse load are +/- 3.1 degrees C, +/- 46 mu epsilon, and +/- 0.01 N/mm, respectively.