Abstract
In this work, we analyze a remote optical sensor system composed of two Fiber Bragg Gratings (FBGs) and one Long Period Grading (LPG) capable of simultaneously sensing the temperature and the refractive index, separated by 50 km from the optical source and the interrogation unit. Since the active components of the system and the sensor head are separated over such a large distance, it is necessary to consider Raman amplification o strengthen the optical signal. We present both experimental measurements and the results of numerical simulations, which describe the signal evolution and predict the measurement results for a remote sensor based on a LPG. The simulation codes are also used to study a hybrid sensor composed of two FBGs with a LPG. We show that the power ratio between the two central wavelengths of the FBG has a linear relation with the change of refractive index of the sensored medium.

Abstract
An intensity curvature sensor using a Photonic Crystal Fiber (PCF) with three coupled cores is proposed. The three cores were aligned and there was an air hole between each two consecutive cores. The fiber had a low air filling fraction, which means that the cores remain coupled in the wavelength region studied. Due to this coupling interference is obtained in the fiber output even if just a single core is illuminated. A configuration using transmission interrogation, which used a section fiber with 0.08 m of PCF as the sensing head, and a configuration using reflection interrogation, which used a section fiber with 0.13 m of PCF as the sensing head, were characterized and compared for curvature sensing. When the fiber is bended along the plane of the cores, one of the lateral cores will be stretched and the other compressed. This changes the coupling between the three cores, changing the optical power intensity. The sensibility of the sensing head was strongly dependent on the direction of bending, having its maximum when the bending direction was along the plane of the cores. A maximum curvature sensitivity of 1.8 dB. m was demonstrated between 0 m and 2.8 m.

Abstract

Abstract
A single-mode nonadiabatic tapered optical fiber (NATOF) sensor was inserted into a fiber loop mirror (FLM) enabling us to tune its sensitivity towards refractive index (RI). The NATOF was fabricated by the heat pulling method, utilizing a CO laser. The adjustment of the polarization controllers (PCs) inserted in loop allowed us to excite different cladding modes in the interferometric taper resulting in different optical paths for the clockwise and the counterclockwise beams. By variation of the PCs' settings, the sensitivity of the sensor for RI in the range from 1.3380 to 1.3510 could be tuned from 876.24 to 1233.07 nm/RIU. Experimental results show that the sensitivity to the external RI increased with the order of the cladding mode.

Abstract
The complexes of ruthenium(II) with phenanthroline (Phen), diphenylphenanthroline (Ph(2)Phen) and with 4,4'-dicarboxy-2,2'-bipyridine acid (Dcbpy) ([Ru(Phen)(2)Dcbpy]Cl(2) and [Ru(Ph(2)Phen)(2)Dcbpy]Cl(2)) were synthesized and the variation of the correspondent fluorescence intensity and lifetime with the pH characterized, Luminescence Intensity, emission wavelength and excited state lifetime all show a typical sigmoid variation with pH in the range 3-9, demonstrating the suitability of this complex for luminescence sensing applications. In aqueous solutions (28% ethanol) the complexes [Ru(Phen)(2)Dcbpy]Cl(2) and [Ru(Ph2Phen)2Dcbpy]Cl2 show, respectively, the following properties: apparent pK(a) of 3.6 +/- 0.4 and 3.7 +/- 0.4; lifetimes of the protonated species 0.46 +/- 0.01 mu s and 0.38 +/- 0.02 mu s and ionised species 0.598 +/- 0.001 mu s and 0.61 +/- 0.08 mu s. The [Ru(Phen)(2)Dcbpy]Cl(2) complex was immobilised in the tip of optical fibers using a hybrid sol-gel procedure based on tetraethoxysilan and phenyltriethoxysilan enabling pH sensitive fiber probes. The immobilised complex shows the following lifetimes: protonated species 1.05 +/- 0.04 mu s and ionised species 1.16 +/- 0.04 mu s. These characteristics show that these ruthenium(II) complexes are good indicators for pH sensing, either in aqueous solution or immobilised in sol-gel, and are well suited for intensity and/or frequency domain interrogation.

Abstract
Cyanobacteria deteriorate the water quality and are responsible for emerging outbreaks and epidemics causing harmful diseases in Humans and animals because of their toxins. Microcystin-LR (MCT) is one of the most relevant cyanotoxin, being the most widely studied hepatotoxin. For safety purposes, the World Health Organization recommends a maximum value of 1 mu g L(-1) of MCT in drinking water. Therefore, there is a great demand for remote and real-time sensing techniques to detect and quantify MCT. In this work a Fabry-Perot sensing probe based on an optical fibre tip coated with a MCT selective thin film is presented. The membranes were developed by imprinting MCT in a sol-gel matrix that was applied over the tip of the fibre by dip coating. The imprinting effect was obtained by curing the sol-gel membrane, prepared with (3-aminopropyl) trimethoxysilane (APTMS), diphenyl-dimethoxysilane (DPDMS), tetraethoxysilane (TEOS), in the presence of MCT. The imprinting effect was tested by preparing a similar membrane without template. In general, the fibre Fabry-Perot with a Molecular Imprinted Polymer (MIP) sensor showed low thermal effect, thus avoiding the need of temperature control in field applications. It presented a linear response to MCT concentration within 0.3-1.4 mu g L(-1) with a sensitivity of -12.4 +/- 0.7 nm L mu g(-1). The corresponding Non-Imprinted Polymer (NIP) displayed linear behaviour for the same MCT concentration range, but with much less sensitivity, of -5.9 +/- 0.2 nm L mu g(-1). The method shows excellent selectivity for MCT against other species co-existing with the analyte in environmental waters. It was successfully applied to the determination of MCT in contaminated samples. The main advantages of the proposed optical sensor include high sensitivity and specificity, low-cost, robustness, easy preparation and preservation.