Abstract
Electric forklifts are extremely important for the world's logistics and industry. Lead acid batteries are the most common energy storage system for electric forklifts; however, to ensure more energy efficiency and less environmental pollution, they are starting to use lithium batteries. All lithium batteries need a battery management system (BMS) for safety, long life cycle and better efficiency. This system is capable to estimate the battery state of charge, state of health and state of function, but those cannot be measured directly and must be estimated indirectly using battery models. Consequently, accurate battery models are essential for implementation of advance BMS and enhance its accuracy. This work presents a comparison between four different models, four different types of optimizers algorithms and seven different experiment designs. The purpose is defining the best model, with the best optimizer, and the best experiment design for battery parameter estimation. This best model is intended for a state of charge estimation on a battery applied on an electric forklift. The nonlinear grey box model with the nonlinear least square method presented a better result for this purpose. This model was estimated with the best experiment design which was defined considering the fit to validation data, the parameter standard deviation and the output variance. With this approach, it was possible to reach more than 80% of fit in different validation data, a non-biased and little prediction error and a good one-step ahead result.

Abstract
Li-ion battery State-of-Charge (SOC) estimation is a complex challenge for battery management systems designers, due to the battery's non-linear behaviour at different operating conditions and ageing levels. As a possible solution, multiple machine learning models have been proposed for SOC estimation throughout the years. These provide an advantage over model-based methods, as they do not require a deep knowledge and study of the battery's internal behaviour. However, many of these proposed models could not be considered due to their complexity. The high number of required stored parameters and/or elevated memory consumption during estimation may pose challenges to the application of these methods. Therefore, in this paper, several feedforward neural network models are proposed for SOC estimation, with an efficient method for online input preprocessing and low parameter requirement in storage. These models are simulated and validated using battery data, taken at different temperatures with several driving cycles and charge cycles, achieving lowest estimation Root Mean Squared Error (RMSE) of 1.096% over the whole validation dataset.

Abstract
To stimulate research in the area of automotive electronics and electric vehicles, the IEEE Vehicular Technology Society (VTS) initiated the Motor Vehicles Challenge. The objective of the 2021 edition of this challenge is to provide a benchmark problem for the energy management of a dual-motor electric vehicle. To solve this, we propose a pragmatic optimization-based energy management system (EMS) that minimizes the instantaneous power consumption of the vehicle through manipulation of torque distribution ratios among the electric motors. Numerical results obtained with the VTS benchmark simulation model demonstrate that the proposed EMS can extend the vehicle range up to 3% when compared to baseline solutions.

Abstract
The offshore wind power industry is an emerging and exponentially growing sector, which calls to a necessity for a cyclical monitoring and inspection to ensure the safety and efficiency of the wind farm facilities. Thus, the emersed (aerial) and immersed (underwater) scenarios must be reconstructed to create a more complete and reliable map that maximizes the observability of all the offshore structures from the wind turbines to the cable arrays, presenting a multi domain scenario.This work proposes the use of an Autonomous Surface Vehicle (ASV) to map both domains simultaneously. As such, it will produce a multi-domain map through the fusion of navigational sensors, GPS and IMU, to localize the vehicle and aid the registration process for the perception sensors, 3D Lidar and Multibeam echosounder sonar. The performed experiments demonstrate the ability of the multi-domain mapping architecture to provide an accurate reconstruction of both scenarios into a single representation using the odometry system as the initial seed to further improve the map with data filtering and registration processes. An error of 0.049 m for the odometry estimation is observed with the GPS/IMU fusion for simulated data and 0.07 m for real field tests. The multi-domain map methodology requires an average of 300 ms per iteration to reconstruct the environment, with an error of at most 0.042 m in simulation.

Abstract
In recent years, autonomous underwater vehicles (AUVs) have gained prominence in the most varied fields of application of underwater missions. The most common solution for recharging their batteries still implies removing them from the water, which is exceptionally costly. The use of Inductive Power Transfer (IPT) technologies allows to mitigate the associated costs and to extend the vehicles' operation time. In consequence, a prototype has been developed, whose objective is to integrate commercially available IPT technologies, while allowing the employment by most of the AUVs. The prototype is a funnel structure and its counterpart aimed to be fixed to a docking station and the AUV respectively. When coupled, it enables the batteries to recharge by electromagnetic induction. Energy transmission has been tested, resulting in encouraging results. This particular solution achieved over 90% efficiency during underwater experiments. The next objective will be to develop a commercial version of the prototype, that allows a direct, practical and effective use of wireless charging technologies within this particular scenario.

Abstract
The maritime industry has been following the paradigm shift toward the automation of typically intelligent procedures, with research regarding autonomous surface vehicles (ASVs) having seen an upward trend in recent years. However, this type of vehicle cannot be employed on a full scale until a few challenges are solved. For example, the docking process of an ASV is still a demanding task that currently requires human intervention. This research work proposes a volumetric convolutional neural network (vCNN) for the detection of docking structures from 3-D data, developed according to a balance between precision and speed. Another contribution of this article is a set of synthetically generated data regarding the context of docking structures. The dataset is composed of LiDAR point clouds, stereo images, GPS, and Inertial Measurement Unit (IMU) information. Several robustness tests carried out with different levels of Gaussian noise demonstrated an average accuracy of 93.34% and a deviation of 5.46% for the worst case. Furthermore, the system was fine-tuned and evaluated in a real commercial harbor, achieving an accuracy of over 96%. The developed classifier is able to detect different types of structures and works faster than other state-of-the-art methods that establish their performance in real environments.