Abstract
We describe an all-fiber Mach-Zehnder interferometric configuration based on a suspended twin-core fiber. Because of the birefringence of the fiber cores, two interferometers are obtained by illuminating the fiber with polarized light. Applying strain, curvature, and temperature to the sensing head, different sensitivities are observed that permit the use of the matrix method to discriminate these three measurands. (C) 2011 Society of Photo-Optical Instrumentation Engineers (SPIE). [DOI: 10.1117/1.3553482]

Abstract
Two new configurations of high-birefringent fiber loop mirror with an output port probe are proposed. The two configurations used two couplers spliced between them with unbalanced arms and one output port is used as the probe sensor. The difference between them is that the section length of high-birefringent fiber is located between the two couplers (first new configuration) or spliced in the output port probe (second new configuration). The second new configuration presents great advantage, especially for remote sensing using only one fiber to the sensing head. The two new configurations were compared with the conventional high-birefringent fiber loop mirror when strain is applied and showed similar sensitivities. The first new configuration is studied as an optical refractometer.

Abstract
A compact fiber-optic inclinometer based on a fiber-taper Michelson interferometric sensor is constructed and demonstrated. The sensor consist of a single symmetrically taper waist of 80 mu m distanced 30 mm from the single-mode fiber end-tip right-angled cleaved. The amplitude of the bending angle of the fiber taper interferometer is obtained by passive interferometric interrogation based on the generation of two quadrature phase-shifted signals from two fiber Bragg gratings with different resonant wavelengths. Optical phase-to-bending sensitivity of similar to 1.13 rad/degree and a bend angle resolution of similar to 0.014 degree/root Hz were achieved.

Abstract
A novel configuration able to measure simultaneously relative humidity and temperature is proposed. The sensing head is based on a long-period fiber grating (LPG) coated with silica nanospheres in-line with a fiber Bragg grating. The polymeric overlay that changes its optical properties when exposed to different humidity levels is deposited onto the LPG using the electrostatic self-assembly technique (ESA), resulting into a humidity-induced shift of the resonance wavelength of the LPG. Considering the humidity range from 20% to 50% RH, a system resolution of 1.6% RH and 2.5 degrees C was achieved. At higher humidity, from 50% to 80% RH, the corresponding resolution values were 2.4% RH and 0.4 degrees C.

Abstract
Different multiwavelength Raman fiber lasers based on a hybrid cavity setup are proposed. The lasing schemes are based in highly birefringent photonic crystal fiber loop mirrors combined with random cavities. The Hi-Bi PCF loop mirrors are characterized by an interferometric output; whereas the random mirrors are created by cooperative Rayleigh scattering due to Raman gain. This configuration allows suppression of Rayleigh associated noise growth, while taking advantage of it as an active part of the laser cavity, enhancing the achievable gain. The proposed fiber lasers present stable operation at room temperature although different output maxima and shapes depending on the fiber loop mirror/random mirror combination.

Abstract
This work describes a fiber optic sensing structure that is sensitive to curvature, and features a low temperature-and strain cross-sensitivity. It is based on multimode interference, and relies on a singlemode-step index multimode-singlemode fiber structure. It was observed that the transmitted optical power in such a layout is highly sensitive to the wavelength of operation, and to the length of the multimode fiber. The optical spectrum exhibits two dominant loss bands, at wavelengths that have similar responses both to temperature and strain, but different responses to curvature. Based on this result, an interrogation approach is proposed that permits substantial sensitivity to curvature (8.7 +/- 0.1 nm m) and residual sensitivities to temperature and strain (0.3 +/- 0.1 pm degrees C(-1) and (-0.06 +/- 0.01) x 10(-6) m m(-1), respectively). The beam-propagation method was employed for modeling the propagation of light along the optical fiber sensing device proposed.