Abstract
The accumulation of lead in several bones of Wistar rats with time was determined and compared for the different types of bones. Two groups were studied: a control group (n = 20), not exposed to lead and a contaminated group (n = 30), exposed to lead from birth, first indirectly through mother's milk, and then directly through a diet containing lead acetate in drinking water (0.2%). Rats age ranged from 1 to 11 months, with approximately 1 month intervals and each of the collections had 3 contaminated rats and 2 control rats. Iliac, femur, tibia-fibula and skull have been analysed by Energy Dispersive X-ray Fluorescence Technique (EDXRF). Samples of formaldehyde used to preserve the bone tissues were also analysed by Electrothermal Atomic Absorption (ETAAS), showing that there was no significant loss of lead from the tissue to the preservative. The bones mean lead concentration of exposed rats range from 100 to 300 mu g g(-1) while control rats never exceeded 10 mu g g(-1). Mean bone lead concentrations were compared and the concentrations were higher in iliac, femur and tibia-fibula and after that skull. However, of all the concentrations in the different collections, only those in the skull were statistically significantly different (p < 0.05) from the other types of bones. Analysis of a radar chart also allowed us to say that these differences tend to diminish with age. The Spearman correlation test applied to mean lead concentrations showed strong and very strong positive correlations between all different types of bones. This test also showed that mean lead concentrations in bones are negatively correlated with the age of the animals. This correlation is strong in iliac and femur and very strong in tibia-fibula and skull. It was also shown that the decrease of lead accumulation with age is made by three plateaus of accumulation, which coincide, in all analysed bones, between 2nd-3rd and 9th-10th months.

Abstract

Abstract
A Fabry-Perot (FP) cavity of simple design and based on a pure silica diaphragm-free hollow tube is proposed. Its operation is based on a first reflection of light at the end of the single-mode fiber that illuminates the silica rod and in a second reflection that takes place at the end of the rod. The FP cavity is characterized for high temperature, pressure and refractive index sensing, showing useful characteristics for the measurement of these three parameters. The diaphragm-free configuration simplifies the measurement of the refractive index of fluids. (C) 2011 Optical Society of America

Abstract
The underground movement of water through soil and rock is an important phenomenon in Civil Engineering. Its study is made more appealing to students if small scale prototypes are used, where several layouts of soil and water in steady state/transient conditions can be studied in detail. A water tank prototype was built with a reflective optical fibre pressure sensor based on a GRIN lens and a mirror. The mirror is connected to an elastic membrane that is deformed when water pressure is applied and the lens is correctly aligned with the mirror and fixed. The distance between the mirror and the lens changes, so the reflective optical power changes as well and it is directly proportional to the water pressure inside the tank. The results obtained for water pressure up to 4 kPa for filling and emptying operations show that the sensor has a linear response for pressure changes between 1.7 kPa and 3.4 kPa with a slope of 181 mu W/kPa for filling and 191 mu W/kPa for emptying. It is also observed some hysteresis that may possibly be reduced by choosing another material for the membrane. Using this type of sensor head it is possible to monitor different pressure points in the small scale prototype using the standard OTDR (Optical Time Domain Reflectometer) equipment.

Abstract
A novel interrogation technique for multiplexing LPG-fiber loop mirrors has been proposed and experimentally demonstrated. Each displacement sensor is formed by a fiber loop mirror combined with a long period grating. This high reflectivity variable mirror is suitable to be interrogated by an OTDR and to be multiplexed in a crosstalk free setup with temperature independence.

Abstract
In this paper, we demonstrate the interrogation of fiber optic intensity sensors by using the combination of the frequency-modulated continuous wave concept with the spectral selective reflectivity of fiber Bragg gratings. Thus, we multiplex these kinds of sensors with this technique having simultaneously a referenced system. The basis of this dual functionality is described and results are presented for the case of interrogation of two multiplexed intensity sensors. Their evaluation permits to establish the conditions to address a sensor network of this type. Also, it is proposed a strategy to implement this sensing approach without the requirement of using optical fiber delay lines in the sensor heads.